(a) Advantages of LED television:
(i) LED television has brighter picture quality
(ii) It is thinner in size
(iii) It uses less power and consumes very less energy.
(iv) Its life span is more.
(v) It is more reliable
(b) Merits of LED bulb:
(i) As there is no filament, there is no loss of energy in the form of heat. It is cooler than the incandescent bulbs
(ii) In comparison with the fluorescent light, the LED bulbs have significantly low power requirement.
(iii) It is not harmful to the environment
(iv) A wide range of colours is possible here.
(v) It is cost-efficient and energy efficient.
(vi) Mercury and other toxic materials are not required.
(vii) One way of overcoming the energy crisis is to use more LED bulbs.

i) The electricity produced in power stations is distributed to all the domestic and industrial consumers through overhead and underground cables.
ii) In our homes, electricity is distributed through the domestic electric circuits wired by the electricians.
iii) The first stage of the domestic circuit is to bring the power supply to the main-box from a distribution panel, such as a transformer.
Main Box Contains:
a) Fuse Box:
i) The fuse box contains either a fuse wire or a miniature circuit breaker (MCB).
ii) The function of the fuse wire or a MCB is to protect the house hold electrical appliances from overloading due to excess current.
iii) An MCB is a switching device, which can be activated automatically as well as manually. It has a spring attached to the switch, which is attracted by an electromagnet when an excess current passes through the circuit.
iv) It has a spring attached to the switch, which is attracted by an electromagnet when an excess current passes through the circuit.
v) Hence, the circuit is broken and the protection of the appliance is ensured.
b) Meter:
i) The meter is used to record the consumption of electrical energy.
Insulated Wire:
i) The electricity is brought to houses by two insulated wires.
ii) Out of these two wires, one wire has a red insulation and is called the "live wire'.
iii) The other wire has a black insulation and is called the 'neutral wire'.
iv) Both, the live wire and the neutral wire enter into a box where the main fuse is connected with the live wire.
v) After the electricity meter, these wires enter into the main switch, which is used to discontinue the electricity supply whenever required.
vi) After the main switch, these wires are connected to live wires of two separate circuits.
5A rating circuit:
i) Out of these two circuits, one circuit is of a 5 A rating, which is used to run the electric appliances with a lower power rating, such as tube lights, bulbs and fans.
15 A rating circuit:
i) The other circuit is of a 15 A rating, which is used to run electric appliances with a high power rating, such as air-conditioners, refrigerators, electric iron and heaters.
ii) It should be noted that all the circuits in a house are connected in parallel, so that the disconnection of one circuit does not affect the other circuit.
iii) One more advantage of the parallel connection of circuits is that each electric appliance gets an equal voltage.
iv) The electricity supplied to your house is actually an alternating current having an electric potential of 220 V.

a) Joule's law of heating:
a) Joule's law of heating states that the heat produced in any resistor is:
(i) Directly proportional to the square of the current passing through the resistor.
(ii) Directly proportional to the resistance of the resistor.
(iii) Directly proportional to the time for which the current is passing through the resistor.
b) Alloy of nickel and chromium have the following properties:
(i) It has high resistivity,
(ii) It has a high melting point,
(iii) It is not easily oxidized.
c) The fuse wire is connected in series, in an electric circuit. When a large current passes through the circuit, the fuse wire melts due to Joule's heating effect and hence the circuit gets disconnected. Therefore, the circuit and the electric appliances are saved from any damage. The fuse wire is made up of a material whose melting point is relatively low.

a) Electric current:
(i) Electric current is often termed as 'current' and it is represented by the symbol 'I'.
(ii) It is defined as the rate of flow of charges in a conductor.
(iii) This means that the electric current represents the amount of charges flowing in any cross-section of a conductor (say a metal wire) in unit time.
(iv) If a net charge 'Q' passes through any cross-section of a conductor in time 't', then the current flowing through the conductor is
\(I=\frac{Q}{t}\)
b) SI unit of electric current:
(i) The SI unit of electric current is ampere (A).
(iii) The current flowing through a conductor is said to be one ampere, when a charge of one coulomb flows across any cross-section of a conductor, in one second. Hence,
\(1 \text { ampere }=\frac{1 \text { coulomb }}{1 \text { second }}\)
c) Ammeter is used to measure the electric current. It should be connected in series in a circuit.

Resistors in series:
i) A series circuit connects the components one after the other to form a 'single loop'.
ii) A series circuit has only one loop through which current can pass.
iii) If the circuit is interrupted at any point in the loop, no current can pass through the circuit and hence no electric appliances connected in the circuit will work.
iv) Series circuits are commonly used in devices such as flashlights.
v) Thus, if resistors are connected end to end, so that the same current passes through each of them, then they are said to be connected in series. 

vi) Let, three resistances R₁, R₂ and R₃ be connected in series.
vii) Let the current flowing through them be I.
viii) According to Ohm's Law, the potential differences V₁, V₂ and V₃ across R₁, R₂ and R₃ respectively, are given by:
\(V_{1}=I R_{1}  \)   ........(1)
\(V_{2}=I R_{2}  \)   .........(2)
\(V_{3}=I R_{3}\)  ..........(3)
The sum of the potential differences across the ends of each resistor is given by:
\(V=V_{1}+V_{2}+V_{3}\)
Using equations (1), (2) and (3), we get
\(\mathbf{V}=\mathbf{I} \mathbf{R}_{1}+\mathbf{I} \mathbf{R}_{2}+\mathbf{I} \mathbf{R}_{3}\)  .........(4)
ix) The effective resistor is a single resistor, which can replace the resistors effectively, so as to allow the same current through the electric circuit.
x) Let, the effective resistance of the series-combination of the resistors, be R₅. Then,
\(\mathbf{V}=\text { I }R_{\mathbf{S}}\)..........(5) 
Combining equations (4) and (5), you get,
\(I R_{S} =I R_{1}+I R_{2}+I R_{3} \)
\(\mathbf{R}_{\mathrm{S}} =R_{1}+R_{2}+R_{3}\) ...........(6)
xi) Thus, you can understand that when a number of resistors are connected in series, their equivalent resistance or effective resistance is equal to the sum of the individual resistances.
xii) When 'n' resistors of equal resistance R are connected in series, the equivalent resistance is 'n R'.
\(\text { i.e., } \mathbf{R}_{\mathrm{S}}=\mathbf{n} \mathbf{R}\)
xiii) The equivalent resistance in a series combination is greater than the highest of the individual resistances.
Resistances in Parallel:
i) A parallel circuit has two or more loops through which current can pass.
ii) If the circuit is disconnected in one of the loops, the current can still pass through the other loop(s).
iii) The wiring in a house consists of parallel circuits.

iv) Consider that three resistors \(R_{1}, R_{2}\) and \(R_{3}\) are connected across two common points A and B.
v) The potential difference across each resistance is the same and equal to the potential difference between A and B.
vi) This is measured using the voltmeter.
vii) The current I arriving at A divides into three branches \(I_{1}, I_{2}\) and \(I_{3}\) passing through \(\mathbf{R}_{1}, \mathbf{R}_{2}\) and \(\mathbf{R}_{3}\) respectively.
According to the Ohm's law, you have,
\(I_{1}=\frac{V}{R_{1}}\) ........ (7)
\(\mathrm{I}_{2}=\frac{\mathbf{V}}{\mathbf{R}_{2}} \) .........(8)
\(\mathbf{I}_{3}=\frac{\mathbf{V}}{\mathbf{R}_{3}}\)  .........(9)
The total current through the circuit is given by,
\(\mathbf{I}=\mathrm{I}_{1}+\mathrm{I}_{\mathbf{2}}+\mathrm{I}_{\mathbf{3}}\)
Using equations (7),(8) and (9), you get,
\(I=\frac{V}{R_{1}}+\frac{V}{R_{2}}+\frac{V}{R_{3}}\) ..........(10)
Let the effective resistance of the parallel combination of resistors be R_P. Then,
\(I=\frac{V}{R_{P}}\) ........ (11)
Combining equations (10) and (11), you have
\(\frac{V}{R_{P}}=\frac{V}{R_{1}}+\frac{V}{R_{2}}+\frac{V}{R_{3}}  \)
\(\frac{1}{R_{P}}=\frac{1}{R_{1}}+\frac{1}{R_{2}}+\frac{1}{R_{3}}\)  ......(12)
viii) Thus, when a number of resistors are connected in parallel, the sum of the reciprocals of the individual resistances is equal to the reciprocal of the effective or equivalent resistance.
ix) When 'n' resistors of equal resistances R are connected in parallel, the equivalent resistance is \(\frac{\mathbf{R}}{\mathbf{n}}\).
i.e., \(\frac{1}{R_{p}}=\frac{1}{R}+\frac{1}{R}+\frac{1}{R} \ldots+\frac{1}{R}=\frac{n}{R}\)  ......(13)
Hence, \(\mathbf{R}_{\mathbf{P}}=\frac{\mathbf{R}}{\mathbf{n}}\)
x) The equivalent resistance in a parallel combination is less than the lowest of the individual resistances.

Given:
\(\mathrm{R}=10 \Omega\) ; original length = l, new length l' = 3l; Area will decrease by 3 times.
\(R^{\prime}=\rho \frac{l^{\prime}}{A^{\prime}}=\rho \frac{31}{A / 3}=\frac{9 \rho l}{A}=9 R=9(10)=90 \Omega\)

Given:
I = 5 A 
t = 1 s
Number of electrons?
\(\mathbf{q}=\mathbf{I\times t}=5 \times 1=5 \mathrm{C} \)
q = ne where n is the number of electrons; e is the charge of an electron which is equal to \(1.6 \times 10^{-19} \mathrm{C}\)
\(n=\frac{q}{e}=\frac{5}{1.6 \times 10^{-19}}=3.125 \times 10^{19}=31.25 \times 10^{18}\) electrons.

Given:
\(\mathrm{R}_{\mathrm{P}}=2 \Omega \)
\(R_{S}=9 \Omega \)
\(\frac{1}{R_{p}}=\frac{1}{R_{1}}+\frac{1}{R_{2}} \)
\(R_{s}=R_{1}+R_{2} \)
\(\mathrm{R}_{\mathrm{P}}=\frac{\mathrm{R}_{1} +\mathrm{R}_{2}}{\mathrm{R}_{1}\mathrm{R}_{2}}\Rightarrow \frac{1}{2}=\frac{\mathrm{R}_{1} +\mathrm{R}_{2}}{\mathrm{R}_{1}\mathrm{R}_{2}} \Rightarrow R_1R_2=2(R_1-R_2) ......(1)\)
\(R_s=R_1+R_2=9 \Omega \Rightarrow R_1= 9-R_2 .....(2)\)
Substitute equation (2) in equation (1)
(9 - R₂) R₂  = 2(9 - R₂ + R₂)
\(9R-R_2^2 = -9r+18=0\frac{18}{-6-3}\)
(R₂ - 3)(R₂ - 6) = 0
R₂ = 3.6
from equation (1) and (2)
\((i) If \ \mathbf{R}_{2}=3 \Omega, \ \mathrm{R}_{1}=6 \Omega \)
\((ii) If \ R_{2}=6 \Omega, \ R_{1}=3 \Omega\)